SDG6000X Series Firmware Update
バージョン
V6.01.01.36R8
SDG6000X Series Firmware Update
バージョン
V6.01.01.36R3
2023-10-30
バージョンの説明
1. Control the IQ output amplitude to avoid distortion
2. Optimize phase noise when using external reference clock
3. Fixed bug in FM modulation on square waveform
4. Fixed bug that the output amplitude of square wave, pulse wave and PRBS is smaller than the set value
5. Fixed bug that VPP was still displayed on the Ul when control the output amplitude in dBm by the SCPI command
6. Fixed the problem of abnormal pulse output when pressing output in burst mode
7. Resolve potential key and touch non response issues
8. Fixed the bug that 128QAM cannot be demodulated
2. Optimize phase noise when using external reference clock
3. Fixed bug in FM modulation on square waveform
4. Fixed bug that the output amplitude of square wave, pulse wave and PRBS is smaller than the set value
5. Fixed bug that VPP was still displayed on the Ul when control the output amplitude in dBm by the SCPI command
6. Fixed the problem of abnormal pulse output when pressing output in burst mode
7. Resolve potential key and touch non response issues
8. Fixed the bug that 128QAM cannot be demodulated
SDG6000X Series Firmware Update
バージョン
V6.01.01.36
2023-10-30
バージョンの説明
1. Allowed one channel to modulate the other
2. Supported Burst in TrueArb mode
3. Supported Burst Counter in Burst mode so the number ofburst trains can be set to > 1 when trigger source =external or manual
4. Added an option to let the SDG start with activatedoutputs
5. Added 50 ohm output impedance text in the Ul
6. Able to remember the digit of a parameter that had been modified
7. Fixed several bugs
a)DDS interpolation bug
b)Switching on/off output causes random phase deviation between channels in Track mode
c)Incorrect square/pulse waveform initialization insome cases
d)Unable to store the level settings for noise
e)Unable to recognize the command MODEePHASE-LOCKED
f)Freezing issue when being written a 20MB long filewith the EasvWVavex
g)The setting"BANDSET" with Waveform = NOISE leads to inconsistent behavior on the Noise Bandwidth of the output signal; The real-time noise bandwidth on channel 2 is changed if an AM sine modulation is switched on channel 1
h)Unable to install the lQ option before 30 trials run out
2. Supported Burst in TrueArb mode
3. Supported Burst Counter in Burst mode so the number ofburst trains can be set to > 1 when trigger source =external or manual
4. Added an option to let the SDG start with activatedoutputs
5. Added 50 ohm output impedance text in the Ul
6. Able to remember the digit of a parameter that had been modified
7. Fixed several bugs
a)DDS interpolation bug
b)Switching on/off output causes random phase deviation between channels in Track mode
c)Incorrect square/pulse waveform initialization insome cases
d)Unable to store the level settings for noise
e)Unable to recognize the command MODEePHASE-LOCKED
f)Freezing issue when being written a 20MB long filewith the EasvWVavex
g)The setting"BANDSET" with Waveform = NOISE leads to inconsistent behavior on the Noise Bandwidth of the output signal; The real-time noise bandwidth on channel 2 is changed if an AM sine modulation is switched on channel 1
h)Unable to install the lQ option before 30 trials run out
SDG6000X Series Firmware Update
バージョン
V6.01.01.35R5B1
2023-10-30
バージョンの説明
1. Changed the upper limit of carrier frequency (sine) in Burst mode from 300 MHz to 500 MHz
2. Added some missing SCPI commands
3. Fixed several bugs
a) Messed up signal after switching from 500 MHz sineto square in independent mode
b)Glitches when outputting pulses under certain circumstances in independent mode
2. Added some missing SCPI commands
3. Fixed several bugs
a) Messed up signal after switching from 500 MHz sineto square in independent mode
b)Glitches when outputting pulses under certain circumstances in independent mode
バージョンの説明
バージョンの説明